ETAS Logo

ETAS - ES1222-A – CAN & K-Line Board

  • Shortcut: Direct to the content of this page
  • Shortcut: Direct to the main navigation
  • To the end of the page
  • ETAS Products
    • Product Search
    • Applications & Solutions
      • ECU Function Development
      • ECU Software Development
      • ECU Testing (HiL)
      • ECU Calibration and Diagnostics
        • Measurement and ECU calibration
        • Integrated ECU Diagnostics
        • In-Vehicle Testing

          Products for
          In-Vehicle Testing

          • ES410 – A/D Module (8-CH)
          • ES411 – A/D Module with Sensor Supply (4-CH)
          • ES420 – Thermo Module (8-CH)
          • ES430 – Lambda Module
          • ES441 – Counter and Frequency Module
          • ES600 – Network Module
          • ES610 – A/D Module
          • ES611 – A/D Module with Sensor Supply
          • ES620 – Thermo Module
          • ES650 – Thermo and A/D Module
          • ES715 – Drive Recorder
          • ES780 – Heads-Up Display
          • ES1000.3 – Housing (VME64x)
          • ES1120 – System Controller Board
          • ES1135 – Simulation/System Controller Board
          • ES1222-A – CAN & K-Line Board
          • ES1232-A – ETK Interface Board
          • ES1303 – A/D Board (16-CH, 100 kHz/CH)
          • ES1310 – D/A Board (8-CH)
          • ES1325 – Digital I/O, PWM I/O and Counter Board
          • LA4 – Lambda Meter
          • AWS2 – Signal Conditioning Unit
        • Testing in the Lab / at the Test Bench
      • Service Diagnostics
    • Download Center
    • Support Center
    • Engineering Services
  • ETAS Group
  • » ETAS Products
  • » Applications & Solutions
  • » ECU Calibration and Diagnostics
  • » In-Vehicle Testing
  • » ES1222-A – CAN & K-Line Board

ES1222-A – CAN & K-Line Board

ES1222-A

The ES1222-A board is designed for powerful rapid prototyping as well as for high performance measurement and calibration applications. The intelligent interface board ES1222.4-A can be used to connect one or more control units to an ES1000 system via the CAN interfaces and/or the K-Line interface. This permits the plug-in card to be used for the following applications:

  • Control unit calibration via CAN bus and/or diagnostic interface
  • Recording of communication data in one or more CAN networks
  • Simulation of CAN nodes in CAN networks
  • Flash programming of control units
  • Control unit diagnostics
  • Connection of external devices to VME bus systems via the CAN interface
  • Measurement of environmental data, e.g., via IPETRONIK modules

Functions at a Glance

  • CAN Interface
  • 4 independent, electrically isolated CAN channels
  • ISO-highspeed physical layer
  • Max. 1 MBaud transmission rate
  • CAN protocol V2.0a/V2.0b (standard/extended identifier)
  • Protocols for measurement and calibration: CAN Calibration
  • Protocol V2.0/V2.1 (standardized ASAP1b CCP), KWP2000 on CAN, XCP on CAN, UDS on CAN (ISO 14229/ISO 15765)
  • K-Line Interface
  • Electrically isolated from VME bus
  • Diagnostic testers compliant with ISO 9141-2
  • Max. 250 kBaud transmission rate
  • Protocols: McMess, KWP2000, Keyword71
  • Cables protected from signal interference by individually shielded channels
  • Firmware update of the ES1222.4-A possible via PC using service software
  • Integrated with ASCET-RP, INTECRIO, and INCA
Go to product family

Page-Tools:

  • Send Page
  • Print Page
  • Contact form
  • Downloads (4)
  • FAQ

  • Copyright ETAS 2008
  • Feedback
  • Glossary
  • Sitemap
  • Terms of Use / Privacy Policy