Technical Data

ES5340-M ES5340-ICE

Analog outputs

Quantity 8 8
(6x single-ended, 2x switchable differential or single-ended for Resolver Sensor) (8x single-ended)
Voltage range -10 V to +10 V (internal reference) -10 V to +10 V (internal reference)
-12 V to +12 V (external reference) -12 V to +12 V (external reference)
Accuracy ±5 mV at 73 °F / 23 °C ±5 mV at 73 °F / 23 °C
Output current ±30 mA (typical) ±30 mA (typical)
Resolution 16 Bit 16 Bit

Digital outputs

Quantity 8 8
Voltage range Open-collector: 0 V to 60 V Open-Collector: 0 V to 60 V
Internal pull-up: 5 V Internal pull-up: 5 V
Output current Max. ±15 mA Max. ±15 mA
Rise time (0 V to 5 V) 2 µs (typical) 2 µs (typical)
Fall time (5 V to 0 V) 3 µs (typical) 3 µs (typical)
Accuracy between 1 Hz and 10 kHz ±0,04 % ±0,04 %
Accuracy between 10 kHz and 100 kHz ±0,4 % ±0,4 %
Duty Cycle 0 % to 100 % 0 % to 100 %
Accuracy duty cycle (50%) between 1 Hz and 10 kHz ±0,2 % to ±2 % (linear) ±0,2 % to ±2 % (linear)
Accuracy duty cycle (50%) between 10 kHz and 100 kHz ±2 % to ±20 % (linear) ±2 % to ±20 % (linear)
Clock rate for PWM generation 8 ns 8 ns

Analog inputs

Quantity 4 4
Voltage range 0 V to +5 V (CH0, CH2) 0 V to +5 V (CH0, CH2)
0 V to +40 V (CH1, CH3) 0 V to +40 V (CH1, CH3)
Resolution 12 Bit 12 Bit
Impedance 1 MΩ 1 MΩ
Detection rate 500 kSamples/s 500 kSamples/s

Digital inputs

Quantity 20 20
Voltage range 0 V to +60 V 0 V to +60 V
Input frequency 125 kHz max 125 kHz max
Resolution 8 ns (125 MHz) 8 ns (125 MHz)
Accuracy between 1 Hz and 10 kHz ±0,04 % ±0,04 %
Accuracy between 10 kHz and 100 kHz ±0,4 % ±0,4 %
Duty Cycle 0 % bis 100 % 0 % bis 100 %
Resolution Duty Cycle ±0,1 % ±0,1 %
Programmable thresholds for high/low detection of input signal Adjustable: 0 V to +10 V Adjustable: 0 V to +10 V

Speed sensor

Supported Systems Resolver Crank / Cam shaft sensor
Digital encoder Knock sensor
Sine encoder
Wave form of the output signal is freely programmable Wave form of the output signal is freely programmable

RPM unit

Angular resolution 0,011 °RA 0,011 °CA
Max. speed 60000 rpm (revolutions per minute) 60000 rpm (revolutions per minute)

Measured value acquisition

Max. number of pulses (per channel and 720° KW) 32
Minimum input pulse width 100 ns
Duty Cycle 0 % to 100 %
Rise and fall time measurement 800 ns to 300 μs
Frequency range 0,1 Hz to 20 kHz
Accuracy of frequency measurement ± (160 ns + 0,1 %)
Accuracy of high time ± (0,5 μs + 0,5 %)

Electrical data

Over voltage protection ±60 V ±60 V
Separation Galvanically isolation of all channels, isolated from PC mass Galvanically isolation of all channels, isolated from PC mass
Controlled cutoff relay for each output Controlled cutoff relay for each output

Supported ETAS software

LABCAR-OPERATOR from V5.0.2 onwards, LABCAR-RTPC from V5.0.2 onwards, Hardware Service Pack (HSP) from V10.4.0 onwards LABCAR-OPERATOR from V5.2.1 HF 1 onwards, LABCAR-RTPC from V6.0.3-1 onwards, Hardware Service Pack (HSP) from V10.4.1 onwards

Environment

Ambient temperature during
operation
+5 °C to +40 °C / +41 °F to + 104 °F +5 °C to +40 °C (+41 °F to +104 °F)
Relative humidity 0 % to 95 % (not condensing) 0 % to 95 % (not condensing)

This product has been developed and released for use in automotive applications. For usage in other domains please contact your ETAS representative.